زرنيخيد الغاليوم

(تم التحويل من Gallium arsenide)
"GaAs" redirects here. For other uses, see Gaas (disambiguation).
Gallium arsenide
Samples of gallium arsenide
Gallium Arsenide (GaAs) 2" wafer.jpg
GaAs wafer of (100) orientation
الأسماء
اسم أيوپاك المفضل
Gallium arsenide
المُعرِّفات
رقم CAS
3D model (JSmol)
ChemSpider
ECHA InfoCard 100.013.741 Edit this at Wikidata
رقم EC
  • 215-114-8
عناوين مواضيع طبية MeSH {{{value}}}
رقم RTECS
  • LW8800000
UNII
UN number 1557
الخصائص
الصيغة الجزيئية GaAs
كتلة مولية 144.645 g/mol[1]
المظهر بلورات رمادية[1]
الرائحة تشبه الثوم حين تكون مبتلة
الكثافة 5.3176 g/cm3[1]
نقطة الانصهار
قابلية الذوبان في الماء غير قابل للذوبان
قابلية الذوبان قابل للذوبان في HCl
غير قابل للذوبان في إيثانول، ميثانول، أسيتون
الفجوة الحزمية 1.441 eV (at 300 K)[2]
حركية الإلكترون 9000 cm2/(V·s) (at 300 K)[2]
القابلية المغناطيسية -16.2×10-6 cgs[4]
التوصيل الحراري 0.56 W/(cm·K) (at 300 K)[3]
معامل الانكسار (nD) 3.3[4]
البنية
البنية البلورية Zinc blende
الزمرة الفراغية T2d-F-43m
ثابت العقد a = 565.315 pm
هندسة
إحداثية 		Tetrahedral
الشكل الجزيئي Linear
المخاطر
صفحة بيانات السلامة External MSDS
ن.م.ع. مخطط تصويري رمز الخطر على الصحة في النظام المنسق عالمياً لتصنيف وعنونة الكيماويات (GHS)
ن.م.ع. كلمة الاشارة DANGER
H350, H360F, H372
P261, P273, P301+P310, P311, P501
NFPA 704 (معيـَّن النار)
Flammability code 0: لن يشتعل. مثل الماءHealth code 3: التعرض لفترة قصيرة قد يتسبب في جروح خطيرة مؤقتة أو باقية. مثل غاز الكلورReactivity code 0: مستقر في العادة، حتى تحت ظروف التعرض للنار، ولا يتفاعل مع الماء. مثل النيتروجين السائلSpecial hazards (white): no codeNFPA 704 four-colored diamond
0
3
0
مركبات ذا علاقة
نيتريد الغاليوم
فوسفيد الغاليوم
أنتيمونيد الغاليوم
ما لم يُذكر غير ذلك، البيانات المعطاة للمواد في حالاتهم العيارية (عند 25 °س [77 °ف]، 100 kPa).
X mark.svgN verify (what is YesYX mark.svgN ?)
مراجع الجدول

زرنيخيد الگاليوم أو أرسنيد الگاليوم أو Gallium arsenide ‏(GaAs وتُنطق: "گاليوم أرسنايد") هو مركب من العنصرين گاليوم وزرنيخ. وهو شبه موصل III/V، ويُستخدَم في صناعة أجهزة مثل microwave frequency integrated circuits, monolithic microwave integrated circuits, infrared light-emitting diodes, laser diodes, solar cells والنوافذ الضوئية.

كثيراً ما يُستخدم GaAs كمادة a substrate للنمو الرأسي لأشباه الموصلات III-V الأخرى بما في ذلك: InGaAs و GaInNAs.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

الاعداد والكيمياء

في المركب، يكون للگاليوم +3 حالات أكسدة. ويمكن اعداد بلورات مفردة من زرنيخيد الگاليوم بثلاث عمليات صناعية:[5]

  • The vertical gradient freeze (VGF) process.[6]
  • Crystal growth using a horizontal zone furnace in the Bridgman-Stockbarger technique, in which gallium and arsenic vapors react, and free molecules deposit on a seed crystal at the cooler end of the furnace.
  • Liquid encapsulated Czochralski (LEC) growth is used for producing high-purity single crystals that can exhibit semi-insulating characteristics (see below). Most GaAs wafers are produced using this process.

Alternative methods for producing films of GaAs include:[5][7]

تأكسد GaAs يحدث في الهواء، مما يقلل من أداء شبه الموصل. The surface can be passivated by depositing a cubic gallium(II) sulfide layer using a tert-butyl gallium sulfide compound such as (t BuGaS) 7.[8]


بلورات شبه عازلة

في وجود فائض من الزرنيخ، تنمو GaAs boules grow with crystallographic defects; specifically, arsenic antisite defects (an arsenic atom at a gallium atom site within the crystal lattice). The electronic properties of these defects (interacting with others) cause the Fermi level to be pinned to near the center of the band gap, so that this GaAs crystal has very low concentration of electrons and holes. This low carrier concentration is similar to an intrinsic (perfectly undoped) crystal, but much easier to achieve in practice. These crystals are called "semi-insulating", reflecting their high resistivity of 107–109 Ω·cm (which is quite high for a semiconductor, but still much lower than a true insulator like glass).[9]

الحفر

Wet etching of GaAs industrially uses an oxidizing agent such as hydrogen peroxide or bromine water,[10] and the same strategy has been described in a patent relating to processing scrap components containing GaAs where the Ga3+  is complexed with a hydroxamic acid ("HA"), for example:[11]

GaAs + H 2O 2 + "HA" → "GaA" complex + H 3AsO 4 + 4 H 2O

This reaction produces arsenic acid.[12]

الإلكترونيات

دوائر منطق رقمي على GaAs

GaAs can be used for various transistor types:[13]

The HBT can be used in integrated injection logic (I2L).

The earliest GaAs logic gate used Buffered FET Logic (BFL).[13]

From 1975ح. 1975 to 1995 the main logic families used were:[13]

مقارنة مع السليكون للإلكترونيات

مزايا GaAs

بعض الخصائص الإلكترونية لزرنيخيد الغاليوم تتفوق على تلك الموجودة في السيليكون. فلديها سرعة أعلى للإلكترونات المشبعة وحركية أعلى للإلكترونات، مما يتيح لترانزستورات زرنيخيد الغاليوم العمل عند ترددات تزيد عن 250 GHz[بحاجة لمصدر]. GaAs devices are relatively insensitive to overheating, owing to their wider energy band gap, and they also tend to create less noise (disturbance in an electrical signal) in electronic circuits than silicon devices, especially at high frequencies. This is a result of higher carrier mobilities and lower resistive device parasitics. These superior properties are compelling reasons to use GaAs circuitry in mobile phones, satellite communications, microwave point-to-point links and higher frequency radar systems. It is also used in the manufacture of Gunn diodes for the generation of microwaves.

Another advantage of GaAs is that it has a direct band gap, which means that it can be used to absorb and emit light efficiently. Silicon has an indirect band gap and so is relatively poor at emitting light.

As a wide direct band gap material with resulting resistance to radiation damage, GaAs is an excellent material for outer space electronics and optical windows in high power applications.

Because of its wide band gap, pure GaAs is highly resistive. Combined with a high dielectric constant, this property makes GaAs a very good substrate for integrated circuits and unlike Si provides natural isolation between devices and circuits. This has made it an ideal material for monolithic microwave integrated circuits (MMICs), where active and essential passive components can readily be produced on a single slice of GaAs.

One of the first GaAs microprocessors was developed in the early 1980s by the RCA Corporation and was considered for the Star Wars program of the United States Department of Defense. These processors were several times faster and several orders of magnitude more radiation resistant than their silicon counterparts, but were more expensive.[15] Other GaAs processors were implemented by the supercomputer vendors Cray Computer Corporation, Convex, and Alliant in an attempt to stay ahead of the ever-improving CMOS microprocessor. Cray eventually built one GaAs-based machine in the early 1990s, the Cray-3, but the effort was not adequately capitalized, and the company filed for bankruptcy in 1995.

Complex layered structures of gallium arsenide in combination with aluminium arsenide (AlAs) or the alloy AlxGa1−xAs can be grown using molecular-beam epitaxy (MBE) or using metalorganic vapor-phase epitaxy (MOVPE). Because GaAs and AlAs have almost the same lattice constant, the layers have very little induced strain, which allows them to be grown almost arbitrarily thick. This allows extremely high performance and high electron mobility HEMT transistors and other quantum well devices.

GaAs is used for monolithic radar power amplifiers (but GaN can be less susceptible to heat damage).[16]

مزايا السليكون

Silicon has three major advantages over GaAs for integrated circuit manufacture. First, silicon is abundant and cheap to process in the form of silicate minerals. The economies of scale available to the silicon industry has also hindered the adoption of GaAs.

In addition, a Si crystal has a very stable structure and can be grown to very large diameter boules and processed with very good yields. It is also a fairly good thermal conductor, thus enabling very dense packing of transistors that need to get rid of their heat of operation, all very desirable for design and manufacturing of very large ICs. Such good mechanical characteristics also make it a suitable material for the rapidly developing field of nanoelectronics. Naturally, a GaAs surface cannot withstand the high temperatures needed for diffusion; however a viable and actively pursued alternative as of the 1980s was ion implantation.[17]

The second major advantage of Si is the existence of a native oxide (silicon dioxide, SiO2), which is used as an insulator. Silicon dioxide can be incorporated onto silicon circuits easily, and such layers are adherent to the underlying silicon. SiO2 is not only a good insulator (with a band gap of 8.9 eV), but the Si-SiO2 interface can be easily engineered to have excellent electrical properties, most importantly low density of interface states. GaAs does not have a native oxide, does not easily support a stable adherent insulating layer, and does not possess the dielectric strength or surface passivating qualities of the Si-SiO2.[17]

Aluminum oxide (Al2O3) has been extensively studied as a possible gate oxide for GaAs (as well as InGaAs).

The third advantage of silicon is that it possesses a higher hole mobility compared to GaAs (500 versus 400 cm2V−1s−1).[18] This high mobility allows the fabrication of higher-speed P-channel field-effect transistors, which are required for CMOS logic. Because they lack a fast CMOS structure, GaAs circuits must use logic styles which have much higher power consumption; this has made GaAs logic circuits unable to compete with silicon logic circuits.

For manufacturing solar cells, silicon has relatively low absorptivity for sunlight, meaning about 100 micrometers of Si is needed to absorb most sunlight. Such a layer is relatively robust and easy to handle. In contrast, the absorptivity of GaAs is so high that only a few micrometers of thickness are needed to absorb all of the light. Consequently, GaAs thin films must be supported on a substrate material.[19]

Silicon is a pure element, avoiding the problems of stoichiometric imbalance and thermal unmixing of GaAs.[20]

Silicon has a nearly perfect lattice; impurity density is very low and allows very small structures to be built (down to 5 nm in commercial production as of 2020[21]). In contrast, GaAs has a very high impurity density,[22] which makes it difficult to build integrated circuits with small structures, so the 500 nm process is a common process for GaAs.[بحاجة لمصدر]

Silicon has about three times the thermal conductivity of GaAs, with less risk of local overheating in high power devices.[16]


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

استخدامات أخرى

خلايا ضوئية عالية الكفاءة، ذات وصلة ثلاثية تغطي الساتل MidSTAR-1.

استخدامات الترانزستور

Gallium arsenide (GaAs) transistors are used in the RF power amplifiers for cell phones and wireless communicating. [23]

الخلايا الشمسية والكواشف

Gallium arsenide is an important semiconductor material for high-cost, high-efficiency solar cells and is used for single-crystalline thin-film solar cells and for multi-junction solar cells.[24]

The first known operational use of GaAs solar cells in space was for the Venera 3 mission, launched in 1965. The GaAs solar cells, manufactured by Kvant, were chosen because of their higher performance in high temperature environments.[25] GaAs cells were then used for the Lunokhod rovers for the same reason.

In 1970, the GaAs heterostructure solar cells were developed by the team led by Zhores Alferov in the USSR,[26][27][28] achieving much higher efficiencies. In the early 1980s, the efficiency of the best GaAs solar cells surpassed that of conventional, crystalline silicon-based solar cells. In the 1990s, GaAs solar cells took over from silicon as the cell type most commonly used for photovoltaic arrays for satellite applications. Later, dual- and triple-junction solar cells based on GaAs with germanium and indium gallium phosphide layers were developed as the basis of a triple-junction solar cell, which held a record efficiency of over 32 % and can operate also with light as concentrated as 2,000 suns. This kind of solar cell powered the Mars Exploration Rovers Spirit and Opportunity, which explored Mars' surface. Also many solar cars utilize GaAs in solar arrays, as did the Hubble Telescope.[29]

GaAs-based devices hold the world record for the highest-efficiency single-junction solar cell at 29.1% (as of 2019). This high efficiency is attributed to the extreme high quality GaAs epitaxial growth, surface passivation by the AlGaAs,[30] and the promotion of photon recycling by the thin film design.[31] GaAs-based photovoltaics are also responsible for the highest efficiency (as of 2022) of conversion of light to electricity, as researchers from the Fraunhofer Institute for Solar Energy Systems achieved a 68.9% efficiency when exposing a GaAs thin film photovoltaic cell to monochromatic laser light with a wavelength of 858 nanometers.[32]

Today, multi-junction GaAs cells have the highest efficiencies of existing photovoltaic cells and trajectories show that this is likely to continue to be the case for the foreseeable future.[33] In 2022, Rocket Lab unveiled a solar cell with 33.3% efficiency[34] based on inverted metamorphic multi-junction (IMM) technology. In IMM, the lattice-matched (same lattice parameters) materials are grown first, followed by mismatched materials. The top cell, GaInP, is grown first and lattice matched to the GaAs substrate, followed by a layer of either GaAs or GaInAs with a minimal mismatch, and the last layer has the greatest lattice mismatch.[35] After growth, the cell is mounted to a secondary handle and the GaAs substrate is removed. A main advantage of the IMM process is that the inverted growth according to lattice mismatch allows a path to higher cell efficiency.

Complex designs of AlxGa1−xAs-GaAs devices using quantum wells can be sensitive to infrared radiation (QWIP).

GaAs diodes can be used for the detection of X-rays.[36]

Future outlook of GaAs solar cells

Despite GaAs-based photovoltaics being the clear champions of efficiency for solar cells, they have relatively limited use in today's market. In both world electricity generation and world electricity generating capacity, solar electricity is growing faster than any other source of fuel (wind, hydro, biomass, and so on) for the last decade.[37] However, GaAs solar cells have not currently been adopted for widespread solar electricity generation. This is largely due to the cost of GaAs solar cells - in space applications, high performance is required and the corresponding high cost of the existing GaAs technologies is accepted. For example, GaAs-based photovoltaics show the best resistance to gamma radiation and high temperature fluctuations, which are of great importance for spacecraft.[38] But in comparison to other solar cells, III-V solar cells are two to three orders of magnitude more expensive than other technologies such as silicon-based solar cells.[39] The primary sources of this cost are the epitaxial growth costs and the substrate the cell is deposited on.

GaAs solar cells are most commonly fabricated utilizing epitaxial growth techniques such as metal-organic chemical vapor deposition (MOCVD) and hydride vapor phase epitaxy (HVPE). A significant reduction in costs for these methods would require improvements in tool costs, throughput, material costs, and manufacturing efficiency.[39] Increasing the deposition rate could reduce costs, but this cost reduction would be limited by the fixed times in other parts of the process such as cooling and heating.[39]

The substrate used to grow these solar cells is usually germanium or gallium arsenide which are notably expensive materials. One of the main pathways to reduce substrate costs is to reuse the substrate. An early method proposed to accomplish this is epitaxial lift-off (ELO),[40] but this method is time-consuming, somewhat dangerous (with its use of hydrofluoric acid), and requires multiple post-processing steps. However, other methods have been proposed that use phosphide-based materials and hydrochloric acid to achieve ELO with surface passivation and minimal post-etching residues and allows for direct reuse of the GaAs substrate.[41] There is also preliminary evidence that spalling could be used to remove the substrate for reuse.[42] An alternative path to reduce substrate cost is to use cheaper materials, although materials for this application are not currently commercially available or developed.[39]

Yet another consideration to lower GaAs solar cell costs could be concentrator photovoltaics. Concentrators use lenses or parabolic mirrors to focus light onto a solar cell, and thus a smaller (and therefore less expensive) GaAs solar cell is needed to achieve the same results.[43] Concentrator systems have the highest efficiency of existing photovoltaics.[44]

So, technologies such as concentrator photovoltaics and methods in development to lower epitaxial growth and substrate costs could lead to a reduction in the cost of GaAs solar cells and forge a path for use in terrestrial applications.

الأجهزة الباعثة للضوء

Band structure of GaAs. The direct gap of GaAs results in efficient emission of infrared light at 1.424 eV (~870 nm).

GaAs has been used to produce near-infrared laser diodes since 1962.[45] It is often used in alloys with other semiconductor compounds for these applications.

N-type GaAs doped with silicon donor atoms (on Ga sites) and boron acceptor atoms (on As sites) responds to ionizing radiation by emitting scintillation photons. At cryogenic temperatures it is among the brightest scintillators known[46][47][48] and is a promising candidate for detecting rare electronic excitations from interacting dark matter, due to the following six essential factors:

  1. Silicon donor electrons in GaAs have a binding energy that is among the lowest of all known n-type semiconductors. Free electrons above 8×1015 per cm3 are not “frozen out" and remain delocalized at cryogenic temperatures.[49]
  2. Boron and gallium are group III elements, so boron as an impurity primarily occupies the gallium site. However, a sufficient number occupy the arsenic site and act as acceptors that efficiently trap ionization event holes from the valence band.[50]
  3. After trapping an ionization event hole from the valence band, the boron acceptors can combine radiatively with delocalized donor electrons to produce photons 0.2 eV below the cryogenic band-gap energy (1.52 eV). This is an efficient radiative process that produces scintillation photons that are not absorbed by the GaAs crystal.[51][52]
  4. There is no afterglow, because metastable radiative centers are quickly annihilated by the delocalized electrons. This is evidenced by the lack of thermally induced luminescence.[53]
  5. N-type GaAs has a high refractive index (~3.5) and the narrow-beam absorption coefficient is proportional to the free electron density and typically several per cm.[54][55][56] One would expect that almost all of the scintillation photons should be trapped and absorbed in the crystal, but this is not the case. Recent Monte Carlo calculations have shown that the high luminosity could be explained of most of the narrow beam absorption is actually optical scattering by the conduction electrons with a cross section of about 10−17 cm2 that allows scintillation photons to escape total internal reflection.[57] This cross section is about 107 times larger than Thomson scattering but comparable to the optical cross section of the conduction electrons in a metal mirror. In the quantum mechanical picture when a photon reaches a lossless thin metal mirror the result is a superposition of two outcomes: (1) the photon is passes through the mirror without loss of energy or (2) the photon loses all of its energy by exciting all available conduction electrons which then emit electric dipole radiation that combines by quantum interference to produce a single photon in a direction that is in accordance with the law of reflection. The probability of transmission is given by T = exp(–z/D), where z is the thickness of the mirror and D is the penetration depth. The probability of reflection is given by R = 1– exp(–z/D). The penetration depth is related to the extinction coefficient k (the imaginary part of the refractive index) by D = λ/(4π k), where λ is the wavelength. The extinction coefficient for 1 µm photons in gold is 6.47 and the penetration depth is 12.3 nm. In that thickness there are 7.3×1016 conduction electrons per cm2, which corresponds to a cross section of 1.4×10−17 cm2. Evidenced by the similar cross sections, photons in n-type GaAs apparently excite the conduction electrons by a similar process (even though they are more widely distributed), but the electric dipole radiation produces photons in random directions that appear as optical scatter. Note that 1 µm photons in gold can excite plasma oscillations (collective oscillations of the conduction electrons) that contribute to their cross section. In n-type GaAs the conduction electron density is far lower and plasma oscillations occur in the far infrared.
  6. N-type GaAs(Si,B) is commercially grown as 10 kg crystal ingots and sliced into thin wafers as substrates for electronic circuits. Boron oxide is used as an encapsulant to prevent the loss of arsenic during crystal growth, but also has the benefit of providing boron acceptors for scintillation.


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fiber optic temperature measurement

For this purpose an optical fiber tip of an optical fiber temperature sensor is equipped with a gallium arsenide crystal. Starting at a light wavelength of 850 nm GaAs becomes optically translucent. Since the spectral position of the band gap is temperature dependent, it shifts about 0.4 nm/K. The measurement device contains a light source and a device for the spectral detection of the band gap. With the changing of the band gap, (0.4 nm/K) an algorithm calculates the temperature (all 250 ms).[58]

Spin-charge converters

GaAs may have applications in spintronics as it can be used instead of platinum in spin-charge converters and may be more tunable.[59]

انظر أيضاً

الهامش

  1. ^ أ ب ت Haynes, p. 4.64
  2. ^ أ ب Haynes, p. 12.90
  3. ^ خطأ استشهاد: وسم <ref> غير صحيح؛ لا نص تم توفيره للمراجع المسماة crc2
  4. ^ أ ب Haynes, p. 12.86
  5. ^ أ ب Moss, S. J.; Ledwith, A. (1987). The Chemistry of the Semiconductor Industry. Springer. ISBN 978-0-216-92005-7.
  6. ^ Scheel, Hans J.; Tsuguo Fukuda. (2003). Crystal Growth Technology. Wiley. ISBN 978-0471490593.
  7. ^ Smart, Lesley; Moore, Elaine A. (2005). Solid State Chemistry: An Introduction. CRC Press. ISBN 978-0-7487-7516-3.
  8. ^ "Chemical vapor deposition from single organometallic precursors" A. R. Barron, M. B. Power, A. N. MacInnes, A. F.Hepp, P. P. Jenkins U.S. Patent 5٬300٬320  (1994)
  9. ^ McCluskey, Matthew D. and Haller, Eugene E. (2012) Dopants and Defects in Semiconductors, pp. 41 and 66, ISBN 978-1439831526
  10. ^ Brozel, M. R.; Stillman, G. E. (1996). Properties of Gallium Arsenide. IEEE Inspec. ISBN 978-0-85296-885-7.
  11. ^ "Oxidative dissolution of gallium arsenide and separation of gallium from arsenic" J. P. Coleman and B. F. Monzyk U.S. Patent 4٬759٬917  (1988)
  12. ^ Lova, Paola; Robbiano, Valentina; Cacialli, Franco; Comoretto, Davide; Soci, Cesare (3 October 2018). "Black GaAs by Metal-Assisted Chemical Etching". ACS Applied Materials & Interfaces. 10 (39): 33434–33440. doi:10.1021/acsami.8b10370. ISSN 1944-8244. PMID 30191706. S2CID 206490133.
  13. ^ أ ب ت Dennis Fisher; I. J. Bahl (1995). Gallium Arsenide IC Applications Handbook. Vol. 1. Elsevier. p. 61. ISBN 978-0-12-257735-2. 'Clear search' to see pages
  14. ^ Ye, Peide D.; Xuan, Yi; Wu, Yanqing; Xu, Min (2010). "Atomic-Layer Deposited High-k/III-V Metal-Oxide-Semiconductor Devices and Correlated Empirical Model". In Oktyabrsky, Serge; Ye, Peide (eds.). Fundamentals of III-V Semiconductor MOSFETs. Springer Science & Business Media. pp. 173–194. doi:10.1007/978-1-4419-1547-4_7. ISBN 978-1-4419-1547-4.
  15. ^ Šilc, Von Jurij; Robič, Borut; Ungerer, Theo (1999). Processor architecture: from dataflow to superscalar and beyond. Springer. p. 34. ISBN 978-3-540-64798-0.
  16. ^ أ ب "A reprieve for Moore's Law: milspec chip writes computing's next chapter". Ars Technica. 2016-06-09. Retrieved 2016-06-14.
  17. ^ أ ب Morgan, D. V.; Board, K. (1991). An Introduction To Semiconductor Microtechnology (2nd ed.). Chichester, West Sussex, England: John Wiley & Sons. p. 137. ISBN 978-0471924784.
  18. ^ Sze, S. M. (1985). Semiconductor Devices Physics and Technology. John Wiley & Sons. Appendix G. ISBN 0-471-87424-8
  19. ^ Single-Crystalline Thin Film. US Department of Energy
  20. ^ Cabrera, Rowan (2019). Electronic Devices and Circuits. EDTECH. p. 35. ISBN 9781839473838. Retrieved 20 January 2022.
  21. ^ Cutress, Dr Ian. "'Better Yield on 5nm than 7nm': TSMC Update on Defect Rates for N5". www.anandtech.com. Retrieved 2020-08-28.
  22. ^ Schlesinger, T.E. (2001). "Gallium Arsenide". Encyclopedia of Materials: Science and Technology. Elsevier. p. 3431-3435. doi:10.1016/B0-08-043152-6/00612-4. ISBN 9780080431529. Retrieved 27 January 2021.
  23. ^ "It's a GaAS: Critical Component for Cell Phone Circuits Grows in 2010". Seeking Alpha. 15 December 2010.
  24. ^ Yin, Jun; Migas, Dmitri B.; Panahandeh-Fard, Majid; Chen, Shi; Wang, Zilong; Lova, Paola; Soci, Cesare (3 October 2013). "Charge Redistribution at GaAs/P3HT Heterointerfaces with Different Surface Polarity". The Journal of Physical Chemistry Letters. 4 (19): 3303–3309. doi:10.1021/jz401485t.
  25. ^ Strobl, G.F.X.; LaRoche, G.; Rasch, K.-D.; Hey, G. (2009). "2: From Extraterrestrial to Terrestrial Applications". High-Efficient Low-Cost Photovoltaics: Recent Developments. Springer. doi:10.1007/978-3-540-79359-5. ISBN 978-3-540-79359-5.
  26. ^ Alferov, Zh. I., V. M. Andreev, M. B. Kagan, I. I. Protasov and V. G. Trofim, 1970, ‘‘Solar-energy converters based on p-n AlxGa1−xAs-GaAs heterojunctions,’’ Fiz. Tekh. Poluprovodn. 4, 2378 (Sov. Phys. Semicond. 4, 2047 (1971))
  27. ^ Nanotechnology in energy applications. im.isu.edu.tw. 16 November 2005 (in Chinese) p. 24
  28. ^ Nobel Lecture by Zhores Alferov at nobelprize.org, p. 6
  29. ^ "Hubble's Instruments Including Control and Support Systems (Cutaway)". HubbleSite.org (in الإنجليزية). Retrieved 2022-10-11.
  30. ^ Schnitzer, I.; et al. (1993). "Ultrahigh spontaneous emission quantum efficiency, 99.7 % internally and 72 % externally, from AlGaAs/GaAs/AlGaAs double heterostructures". Applied Physics Letters. 62 (2): 131. Bibcode:1993ApPhL..62..131S. doi:10.1063/1.109348. S2CID 14611939.
  31. ^ Wang, X.; et al. (2013). "Design of GaAs Solar Cells Operating Close to the Shockley–Queisser Limit". IEEE Journal of Photovoltaics. 3 (2): 737. doi:10.1109/JPHOTOV.2013.2241594. S2CID 36523127.
  32. ^ "Record Efficiency of 68.9% for GaAs Thin Film Photovoltaic Cell Under Laser Light - Fraunhofer ISE". Fraunhofer Institute for Solar Energy Systems ISE (in الإنجليزية). Retrieved 2022-10-11.
  33. ^ Yamaguchi, Masafumi (2021-04-14), Muzibur Rahman, Mohammed; Mohammed Asiri, Abdullah; Khan, Anish et al., eds. (in en), High-Efficiency GaAs-Based Solar Cells, IntechOpen, doi:10.5772/intechopen.94365, ISBN 978-1-83968-260-5, https://www.intechopen.com/books/post-transition-metals/high-efficiency-gaas-based-solar-cells, retrieved on 2022-10-11 
  34. ^ "Rocket Lab unveils space solar cell with 33.3% efficiency". solarparts (in الكورية). Retrieved 2022-10-12.
  35. ^ Duda, Anna; Ward, Scott; Young, Michelle (February 2012). "Inverted Metamorphic Multijunction (IMM) Cell Processing Instructions" (PDF). National Renewable Energy Laboratory. Retrieved October 11, 2022.{{cite web}}: CS1 maint: url-status (link)
  36. ^ Glasgow University report on CERN detector. Ppewww.physics.gla.ac.uk. Retrieved on 2013-10-16.
  37. ^ Haegel, Nancy; Kurtz, Sarah (November 2021). "Global Progress Toward Renewable Electricity: Tracking the Role of Solar". IEEE Journal of Photovoltaics (published 20 September 2021). 11 (6): 1335–1342. doi:10.1109/JPHOTOV.2021.3104149. ISSN 2156-3381. S2CID 239038321 – via IEEE Xplore.
  38. ^ Papež, Nikola; Gajdoš, Adam; Dallaev, Rashid; Sobola, Dinara; Sedlák, Petr; Motúz, Rastislav; Nebojsa, Alois; Grmela, Lubomír (2020-04-30). "Performance analysis of GaAs based solar cells under gamma irradiation". Applied Surface Science (in الإنجليزية). 510: 145329. Bibcode:2020ApSS..51045329P. doi:10.1016/j.apsusc.2020.145329. ISSN 0169-4332. S2CID 213661192.
  39. ^ أ ب ت ث Horowitz, Kelsey A.; Remo, Timothy W.; Smith, Brittany; Ptak, Aaron J. (2018-11-27). "A Techno-Economic Analysis and Cost Reduction Roadmap for III-V Solar Cells". doi:10.2172/1484349. OSTI 1484349. S2CID 139380070. {{cite journal}}: Cite journal requires |journal= (help)
  40. ^ Konagai, Makoto; Sugimoto, Mitsunori; Takahashi, Kiyoshi (1978-12-01). "High efficiency GaAs thin film solar cells by peeled film technology". Journal of Crystal Growth (in الإنجليزية). 45: 277–280. Bibcode:1978JCrGr..45..277K. doi:10.1016/0022-0248(78)90449-9. ISSN 0022-0248.
  41. ^ Cheng, Cheng-Wei; Shiu, Kuen-Ting; Li, Ning; Han, Shu-Jen; Shi, Leathen; Sadana, Devendra K. (2013-03-12). "Epitaxial lift-off process for gallium arsenide substrate reuse and flexible electronics". Nature Communications (in الإنجليزية). 4 (1): 1577. Bibcode:2013NatCo...4.1577C. doi:10.1038/ncomms2583. ISSN 2041-1723. PMID 23481385. S2CID 205315999.
  42. ^ Metaferia, Wondwosen; Chenenko, Jason; Packard, Corinne E.; Ptak, Aaron J.; Schulte, Kevin L. (2021-06-20). "(110)-Oriented GaAs Devices and Spalling as a Platform for Low-Cost III-V Photovoltaics". 2021 IEEE 48th Photovoltaic Specialists Conference (PVSC). Fort Lauderdale, FL, USA: IEEE: 1118–1120. doi:10.1109/PVSC43889.2021.9518754. ISBN 978-1-6654-1922-2. OSTI 1869274. S2CID 237319505.
  43. ^ Papež, Nikola; Dallaev, Rashid; Ţălu, Ştefan; Kaštyl, Jaroslav (2021-06-04). "Overview of the Current State of Gallium Arsenide-Based Solar Cells". Materials (in الإنجليزية). 14 (11): 3075. Bibcode:2021Mate...14.3075P. doi:10.3390/ma14113075. ISSN 1996-1944. PMC 8200097. PMID 34199850.
  44. ^ Philipps, Simon P.; Bett, Andreas W.; Horowitz, Kelsey; Kurtz, Sarah (2015-12-01). "Current Status of Concentrator Photovoltaic (CPV) Technology". doi:10.2172/1351597. OSTI 1351597. {{cite journal}}: Cite journal requires |journal= (help)
  45. ^ Hall, Robert N.; Fenner, G. E.; Kingsley, J. D.; Soltys, T. J.; Carlson, R. O. (1962). "Coherent Light Emission From GaAs Junctions". Physical Review Letters. 9 (9): 366–369. Bibcode:1962PhRvL...9..366H. doi:10.1103/PhysRevLett.9.366.
  46. ^ Derenzo, S.; Bourret, E.; Hanrahan, S.; Bizarri, G. (2018). "Cryogenic scintillation properties of n-type GaAs for the direct detection of MeV/c2 dark matter". Journal of Applied Physics. 123 (11): 114501. arXiv:1802.09171. Bibcode:2018JAP...123k4501D. doi:10.1063/1.5018343. S2CID 56118568
  47. ^ Vasiukov, S.; Chiossi, F.; Braggio, C.; Carugno, G.; Moretti, F.; Bourret, E.; Derenzo, S. (2019). "GaAs as a Bright Cryogenic Scintillator for the Detection of Low-Energy Electron Recoils from MeV/c2 Dark Matter". IEEE Transactions on Nuclear Science. 66 (11): 2333–2337. Bibcode:2019ITNS...66.2333V. doi:10.1109/TNS.2019.2946725. S2CID 208208697
  48. ^ Derenzo, S.; Bourret, E.; Frank-Rotsch, C.; Hanrahan, S.; Garcia-Sciveres, M. (2021). "How silicon and boron dopants govern the cryogenic scintillation properties of n-type GaAs". Nuclear Instruments and Methods in Physics Research Section A. 989: 164957. arXiv:2012.07550. Bibcode:2021NIMPA.98964957D. doi:10.1016/j.nima.2020.164957. S2CID 229158562
  49. ^ Benzaquen, M.; Walsh, D.; Mazuruk, K. (1987). "Conductivity of n-type GaAs near the Mott transition". Physical Review B. 36 (9): 4748–4753. Bibcode:1987PhRvB..36.4748B. doi:10.1103/PhysRevB.36.4748. PMID 9943488
  50. ^ Pätzold, O.; Gärtner, G.; Irmer, G. (2002). "Boron Site Distribution in Doped GaAs". Physica Status Solidi B. 232 (2): 314–322. Bibcode:2002PSSBR.232..314P. doi:10.1002/1521-3951(200208)232:2<314::AID-PSSB314>3.0.CO;2-#.
  51. ^ Vasiukov, S.; Chiossi, F.; Braggio, C.; Carugno, G.; Moretti, F.; Bourret, E.; Derenzo, S. (2019). "GaAs as a Bright Cryogenic Scintillator for the Detection of Low-Energy Electron Recoils from MeV/c2 Dark Matter". IEEE Transactions on Nuclear Science. 66 (11): 2333–2337. Bibcode:2019ITNS...66.2333V. doi:10.1109/TNS.2019.2946725. S2CID 208208697
  52. ^ Derenzo, S.; Bourret, E.; Frank-Rotsch, C.; Hanrahan, S.; Garcia-Sciveres, M. (2021). "How silicon and boron dopants govern the cryogenic scintillation properties of n-type GaAs". Nuclear Instruments and Methods in Physics Research Section A. 989: 164957. arXiv:2012.07550. Bibcode:2021NIMPA.98964957D. doi:10.1016/j.nima.2020.164957. S2CID 229158562
  53. ^ Derenzo, S.; Bourret, E.; Hanrahan, S.; Bizarri, G. (2018). "Cryogenic scintillation properties of n-type GaAs for the direct detection of MeV/c2 dark matter". Journal of Applied Physics. 123 (11): 114501. arXiv:1802.09171. Bibcode:2018JAP...123k4501D. doi:10.1063/1.5018343. S2CID 56118568
  54. ^ Spitzer, W. G.; Whelan, J. M. (1959). "Infrared Absorption and Electron Effective Mass in n-type Gallium Arsenide". Physical Review. 114 (1): 59–63. Bibcode:1959PhRv..114...59S. doi:10.1103/PhysRev.114.59
  55. ^ Sturge, M. D. (1962). "Optical Absorption of Gallium Arsenide between 0.6 and 2.75 eV". Physical Review. 127 (3): 768–773. Bibcode:1962PhRv..127..768S. doi:10.1103/PhysRev.127.768
  56. ^ Osamura, Kozo; Murakami, Yotaro (1972). "Free Carrier Absorption in n-GaAs". Japanese Journal of Applied Physics. 11 (3): 365–371. Bibcode:1972JaJAP..11..365O. doi:10.1143/JJAP.11.365. S2CID 120981460
  57. ^ Derenzo, Stephen E. (2022). "Monte Carlo calculations of the extraction of scintillation light from cryogenic n-type GaAs". Nuclear Instruments and Methods in Physics Research Section A. 1034: 166803. arXiv:2203.15056. Bibcode:2022NIMPA103466803D. doi:10.1016/j.nima.2022.166803. S2CID 247779262.
  58. ^ A New Fiber Optical Thermometer and Its Application for Process Control in Strong Electric, Magnetic, and Electromagnetic Fields. optocon.de (PDF; 2,5 MB)
  59. ^ GaAs forms basis of tunable spintronics. compoundsemiconductor.net. September 2014

وصلات خارجية

قالب:Arsenides

الكلمات الدالة:
تمّ الاسترجاع من "https://www.marefa.org/w/index.php?title=زرنيخيد_الغاليوم&oldid=2971775"